Question: Does the ice maker lever go up or down?

When its in the down position a lever will strike and close the on/off switch so that the ice maker is on. The wire arm is pulled down by a small spring. Each time the ice maker starts to harvest the wire arm will slowly rise up so that the ice dumps out under it and then the arm slowly comes back down.

What position should the ice maker ARM be in?

Ice maker control arms should flip up and down easily. If the ice maker control arm, connecting rod, or shut-off arm is broken or not installed properly, ice production may stop, or the ice bin may overflow as the ice maker continues to produce ice after the ice bin is already full.

How does ice maker arm work?

Just before the cubes are pushed out of the icemaker, the cam catches hold of the shut-off arm, lifting it up. After the cubes are ejected, the arm falls down again. When the arm reaches its lowest resting position, it throws a switch in the circuit, which activates the water valve to begin another cycle.

How do I adjust the water flow on my ice maker?

Turn the small adjustment set screw on the upper, middle right hand side of your ice maker a half of a turn with a Phillips or flat head screwdriver, depending on the screw your ice maker has. Turning the screw clockwise will decrease the water level and turning it counterclockwise will increase the water level.

How do you install an ice maker lever?

1:302:47How To: Whirlpool/KitchenAid/Maytag Ice Maker Shut Off Arm W11342242YouTubeStart of suggested clipEnd of suggested clipOnce you have it pushed all the way in we can reach back and snap the other end into the filled cup.MoreOnce you have it pushed all the way in we can reach back and snap the other end into the filled cup. And once you have it installed on both sides it should swing freely.

How do I know if ice maker is working?

To check if the icemaker itself is working:If the icemaker mold is empty, you can manually pour about 4 ounces of water in the icemaker mold.Wait about 2 hours.If the icemaker has dropped ice cubes out from the mold, you know the icemaker itself is working.

How do you know if the ice maker is on?

To turn ON the icemaker, set the power switch to I (ON). When the icemaker is turned on the green power light will come on. To turn OFF the icemaker, set the power switch to O (OFF).

What triggers ice maker to fill?

At the beginning of the cycle, an electrical signal is sent to a water valve to fill the ice mold with water. This cycle will continue until the shut-off arm installed at the front of the ice maker sends a signal that the ice cubes are stacked to its capacity.

How do I adjust my refrigerator ice maker?

1:202:43Ice Maker Troubleshooting and Adjusting - Cube Size - YouTubeYouTube

What is a feeler arm in an ice maker?

The feeler arm is the wire arm that shuts the icemaker down then it hits the ice. There is a spring inside the icemaker head that will force the arm back down after the motor lifts it up. If this spring is broken the arm will not come back down to push the switch as if it were hitting ice, shutting the icemaker off.

How do I test my ice maker?

0:063:59Ice Maker - Cycle Test - YouTubeYouTube

How do I force my Frigidaire ice maker to cycle?

How to Force an Ice Maker to CycleOpen the freezer door to remove the ice bin from below the ice maker.Empty the ice from the bin. Press the ice maker toggle switch to the On setting if it is not already activated.Pop off the front cover of the ice maker with the tip of a flat-blade screwdriver.More items •26 Sep 2017

Should feeler arm be up or down?

Once the ice is used and the ice level drops the arm should drop down position so that the ice maker will be on. You should feel the spring tension as you raise and lower the arm. You should also be able to hear a faint click of the on/off switch when the arm is at the lowest point.

Join us

Find us at the office

Heston- Cat street no. 49, 44572 Yerevan, Armenia

Give us a ring

Kaeli Mastroddi
+51 487 505 696
Mon - Fri, 8:00-19:00

Contact us